Add --keep-going mode to all.sh. In this mode, if a test fails, keep
running the subsequent tests. If a build fails, skip any tests of this
build and move on to the next tests. Errors in infrastructure, such as
git or cmake runs, remain fatal. Print an error summary at the end of
the run, and return a nonzero code if there was any failure.
In known terminal types, use color to highlight errors.
On a fatal signal, interrupt the run and report the errors so far.
Port wait_server_start from ssl-opt.sh to compat.sh, instead of just
using "sleep 1". This solves the problem that on a heavily loaded
machine, sleep 1 is sometimes not enough (we had CI failures because
of this). This is also faster on a lightly-loaded machine (execution
time reduced from ~8min to ~6min on my machine).
In wait_server_start, fork less. When lsof is present, call it on the
expected process. This saves a few percent of execution time on a
lightly loaded machine. Also, sleep for a short duration rather than
using a tight loop.
Previously, MAC validation for an incoming record proceeded as follows:
1) Make a copy of the MAC contained in the record;
2) Compute the expected MAC in place, overwriting the presented one;
3) Compare both.
This resulted in a record buffer overflow if truncated MAC was used, as in this
case the record buffer only reserved 10 bytes for the MAC, but the MAC
computation routine in 2) always wrote a full digest.
For specially crafted records, this could be used to perform a controlled write of
up to 6 bytes past the boundary of the heap buffer holding the record, thereby
corrupting the heap structures and potentially leading to a crash or remote code
execution.
This commit fixes this by making the following change:
1) Compute the expected MAC in a temporary buffer that has the size of the
underlying message digest.
2) Compare to this to the MAC contained in the record, potentially
restricting to the first 10 bytes if truncated HMAC is used.
A similar fix is applied to the encryption routine `ssl_encrypt_buf`.
This commit adds a build with default config except
MBEDTLS_SSL_MAX_FRAGMENT_LENGTH to all.sh, as well as a run of the MFL-related
tests in ssl-opt.sh.
Some tests in ssl-opt.sh require MBEDTLS_SSL_MAX_CONTENT_LEN to be set to its
default value of 16384 to succeed. While ideally such a dependency should not
exist, as a short-term remedy this commit adds a small check that will at least
lead to graceful exit if that assumption is violated.
This commit adds four tests to ssl-opt.sh testing the library's behavior when
`mbedtls_ssl_write` is called with messages beyond 16384 bytes. The combinations
tested are TLS vs. DTLS and MBEDTLS_SSL_MAX_FRAGMENT_LENGTH enabled vs. disabled.
For a key of size 8N+1, check that the first byte after applying the
public key operation is 0 (it could have been 1 instead). The code was
incorrectly doing a no-op check instead, which led to invalid
signatures being accepted. Not a security flaw, since you would need the
private key to craft such an invalid signature, but a bug nonetheless.
The check introduced by the previous security fix was off by one. It
fixed the buffer overflow but was not compliant with the definition of
PSS which technically led to accepting some invalid signatures (but
not signatures made without the private key).
Fix buffer overflow in RSA-PSS signature verification when the hash is
too large for the key size. Found by Seth Terashima, Qualcomm.
Added a non-regression test and a positive test with the smallest
permitted key size for a SHA-512 hash.
This commit adds regression tests for the bug when we didn't parse the
Signature Algorithm extension when renegotiating. (By nature, this bug
affected only the server)
The tests check for the fallback hash (SHA1) in the server log to detect
that the Signature Algorithm extension hasn't been parsed at least in
one of the handshakes.
A more direct way of testing is not possible with the current test
framework, since the Signature Algorithm extension is parsed in the
first handshake and any corresponding debug message is present in the
logs.
Previously, 2048-bit and 4096-bit RSA key files had their bitsize indicated in their filename, while the original
1024-bit keys hadn't. This commit unifies the naming scheme by always indicating the bitsize in the filename.
