Add --keep-going mode to all.sh. In this mode, if a test fails, keep
running the subsequent tests. If a build fails, skip any tests of this
build and move on to the next tests. Errors in infrastructure, such as
git or cmake runs, remain fatal. Print an error summary at the end of
the run, and return a nonzero code if there was any failure.
In known terminal types, use color to highlight errors.
On a fatal signal, interrupt the run and report the errors so far.
If timing_timer_simple fails because it detects that timers are likely
to never expire (e.g. going backward or not incrementing), skip all
tests that rely on timers.
Do test mbedtls_timing_hardclock. We can't reliably test much about
it, but at least test that it doesn't crash, isn't constant, and
doesn't look completely random.
New set of unit tests for the timing module, instead of just running
the selftest function.
The selftest function sometimes fails on a heavily loaded
machine (such as a typical continuous integration system). Because of
the all-in-one nature of the test and because the exact load pattern
can be hard to reproduce, it is difficult to diagnose failures of CI
runs with selftest. The new tests are more separated and I strove to
point out potential failure modes in comments.
* mbedtls_timing_hardclock: not tested. This function gives so few
guarantees that there isn't much to test, and it is hard to test
reliably because clock cycles don't easily relate to time in any
remotely portable way. This function isn't used in the library
anyway, it's only there for benchmark programs.
* mbedtls_timing_get_timer: tested by setting a timer and verifying
that it reaches its target, and by verifying that a timer started
later than another always has a smaller elapsed time.
* mbedtls_set_alarm: tested by setting an alarm, busy-waiting for it
and measuring the elapsed time with a timer.
* mbedtls_timing_set_delay, mbedtls_timing_get_delay: tested by
setting a delay object and watching it go through its two delay
values, using a timer to check that the delays are passed at the
expected time.
The tests pass under light to moderate load, but some of them can be
defeated with sufficiently heavy load. This is unavoidable since the
test process to be effectively suspended for any length of time,
making us think that a timer has gone on for too long.
* development:
Don't split error code description across multiple lines
Register new error code in error.h
Move deprecation to separate section in ChangeLog
Extend scope of ERR_RSA_UNSUPPORTED_OPERATION error code
Adapt RSA test suite
Adapt ChangeLog
Deprecate usage of RSA primitives with wrong key type
* restricted/pr/397:
Don't split error code description across multiple lines
Register new error code in error.h
Move deprecation to separate section in ChangeLog
Extend scope of ERR_RSA_UNSUPPORTED_OPERATION error code
Adapt RSA test suite
Adapt ChangeLog
Deprecate usage of RSA primitives with wrong key type
Port wait_server_start from ssl-opt.sh to compat.sh, instead of just
using "sleep 1". This solves the problem that on a heavily loaded
machine, sleep 1 is sometimes not enough (we had CI failures because
of this). This is also faster on a lightly-loaded machine (execution
time reduced from ~8min to ~6min on my machine).
In wait_server_start, fork less. When lsof is present, call it on the
expected process. This saves a few percent of execution time on a
lightly loaded machine. Also, sleep for a short duration rather than
using a tight loop.
Add a DTLS small packet test for each of the following combinations:
- DTLS version: 1.0 or 1.2
- Encrypt then MAC extension enabled
- Truncated HMAC extension enabled
Large packets tests for DTLS are currently not possible due to parameter
constraints in ssl_server2.
This commit ensures that there is a small packet test for at least any
combination of
- SSL/TLS version: SSLv3, TLS 1.0, TLS 1.1 or TLS 1.2
- Stream cipher (RC4) or Block cipher (AES)
- Usage of Encrypt then MAC extension [TLS only]
- Usage of truncated HMAC extension [TLS only]
Noticed that the test cases in ssl-opt.sh exercising the truncated HMAC
extension do not depend on MBEDTLS_SSL_TRUNCATED_HMAC being enabled in
config.h. This commit fixes this.
Previously, MAC validation for an incoming record proceeded as follows:
1) Make a copy of the MAC contained in the record;
2) Compute the expected MAC in place, overwriting the presented one;
3) Compare both.
This resulted in a record buffer overflow if truncated MAC was used, as in this
case the record buffer only reserved 10 bytes for the MAC, but the MAC
computation routine in 2) always wrote a full digest.
For specially crafted records, this could be used to perform a controlled write of
up to 6 bytes past the boundary of the heap buffer holding the record, thereby
corrupting the heap structures and potentially leading to a crash or remote code
execution.
This commit fixes this by making the following change:
1) Compute the expected MAC in a temporary buffer that has the size of the
underlying message digest.
2) Compare to this to the MAC contained in the record, potentially
restricting to the first 10 bytes if truncated HMAC is used.
A similar fix is applied to the encryption routine `ssl_encrypt_buf`.
For a key of size 8N+1, check that the first byte after applying the
public key operation is 0 (it could have been 1 instead). The code was
incorrectly doing a no-op check instead, which led to invalid
signatures being accepted. Not a security flaw, since you would need the
private key to craft such an invalid signature, but a bug nonetheless.
The check introduced by the previous security fix was off by one. It
fixed the buffer overflow but was not compliant with the definition of
PSS which technically led to accepting some invalid signatures (but
not signatures made without the private key).
Fix buffer overflow in RSA-PSS signature verification when the hash is
too large for the key size. Found by Seth Terashima, Qualcomm.
Added a non-regression test and a positive test with the smallest
permitted key size for a SHA-512 hash.
This commit adds regression tests for the bug when we didn't parse the
Signature Algorithm extension when renegotiating. (By nature, this bug
affected only the server)
The tests check for the fallback hash (SHA1) in the server log to detect
that the Signature Algorithm extension hasn't been parsed at least in
one of the handshakes.
A more direct way of testing is not possible with the current test
framework, since the Signature Algorithm extension is parsed in the
first handshake and any corresponding debug message is present in the
logs.
The test case parses an RSA private key with N=P=Q=D=E=1 and expects a failure from the PK layer. With the weakened
semantics of `mbedtls_rsa_complete`, the latter won't throw an error on that key in case if MBEDTLS_RSA_NO_CRT is
set. This commit modifies the test case to use N=2 which is rejected by `mbedtls_rsa_complete` regardless of whether
MBEDTLS_RSA_NO_CRT is set or not.
The number of loop iterations per candidate in `mbedtls_deduce_primes` was off
by one. This commit corrects this and removes a toy non-example from the RSA
test suite, as it seems difficult to have the function fail on small values of N
even if D,E are corrupted.
This commit adds regression tests for the bug when we didn't parse the
Signature Algorithm extension when renegotiating. (By nature, this bug
affected only the server)
The tests check for the fallback hash (SHA1) in the server log to detect
that the Signature Algorithm extension hasn't been parsed at least in
one of the handshakes.
A more direct way of testing is not possible with the current test
framework, since the Signature Algorithm extension is parsed in the
first handshake and any corresponding debug message is present in the
logs.
This commit splits off the RSA helper functions into separate headers and
compilation units to have a clearer separation of the public RSA interface,
intended to be used by end-users, and the helper functions which are publicly
provided only for the benefit of designers of alternative RSA implementations.
The tests now accept two result parameters, one for the expected result of the
completion call, and one for the expected result of the subsequent sanity
check.
The change modifies the template code in tests/suites/helpers.function
and tests/suites/main.function so that error messages are printed to
stdout instead of being discarded. This makes errors visible regardless
of the --verbose flag being passed or not to the test suite programs.
The change modifies the template code in tests/suites/helpers.function
and tests/suites/main.function so that error messages are printed to
stdout instead of being discarded. This makes errors visible regardless
of the --verbose flag being passed or not to the test suite programs.
Add a test to ssl-opt.sh that parses the client and server debug
output and then checks that the Unix timestamp in the ServerHello
message is within acceptable bounds.
Extend the run_test function in ssl-opt.sh so that it accepts the -f
and -F options. These parameters take an argument which is the name of
a shell function that will be called by run_test and will be given the
client input and output debug log. The idea is that these functions are
defined by each test and they can be used to do some custom check
beyon those allowed by the pattern matching capabilities of the
run_test function.
Add a test case calling ssl_set_hostname twice to test_suite_ssl.
When run in CMake build mode ASan, this catches the current leak,
but will hopefully be fine with the new version.
Add a test to ssl-opt.sh that parses the client and server debug
output and then checks that the Unix timestamp in the ServerHello
message is within acceptable bounds.
Extend the run_test function in ssl-opt.sh so that it accepts the -f
and -F options. These parameters take an argument which is the name of
a shell function that will be called by run_test and will be given the
client input and output debug log. The idea is that these functions are
defined by each test and they can be used to do some custom check
beyon those allowed by the pattern matching capabilities of the
run_test function.
As the new PKCS v1.5 verification function opaquely compares an expected encoding to the given one, it cannot
distinguish multiple reasons of failure anymore and instead always returns MBEDTLS_ERR_RSA_VERIFY_FAILED. This
necessitates some modifications to the expected return values of some tests verifying signatures with bad padding.
This commit adds some tests to the RSA test suite verifying that RSA PKCS-v15 signatures with non-reduced length
encodings are refuted. Details are provided via comments in the test suite data file.
Add a test case calling ssl_set_hostname twice to test_suite_ssl.
When run in CMake build mode ASan, this catches the current leak,
but will hopefully be fine with the new version.
This commit adds a flag to the RSA import/export tests indicating whether it is
expected that a full RSA keypair can be set up from the provided parameters.
Further, the tests of `mbedtls_rsa_import` and `mbedtls_rsa_import_raw` are
expanded to perform key checks and an example encryption-decryption.
Some tests in ssl-opt.sh require MBEDTLS_SSL_MAX_CONTENT_LEN to be set to its
default value of 16384 to succeed. While ideally such a dependency should not
exist, as a short-term remedy this commit adds a small check that will at least
lead to graceful exit if that assumption is violated.
A bug in the dhm_check_range() function makes it pass even when the
parameters are not in the range. This commit adds tests for signalling
this problem as well as a couple of other negative tests.
This commit adds four tests to ssl-opt.sh testing the library's behavior when
`mbedtls_ssl_write` is called with messages beyond 16384 bytes. The combinations
tested are TLS vs. DTLS and MBEDTLS_SSL_MAX_FRAGMENT_LENGTH enabled vs. disabled.
This commit adds a build with default config except
MBEDTLS_SSL_MAX_FRAGMENT_LENGTH to all.sh, as well as a run of the MFL-related
tests in ssl-opt.sh.
This commit renames the test-only flag MBEDTLS_ENTROPY_HAVE_STRONG to ENTROPY_HAVE_STRONG to make it more transparent
that it's an internal flag, and also to content the testscript tests/scripts/check-names.pl which previously complained
about the macro occurring in a comment in `entropy.c` without being defined in a library file.
Previously, 2048-bit and 4096-bit RSA key files had their bitsize indicated in their filename, while the original
1024-bit keys hadn't. This commit unifies the naming scheme by always indicating the bitsize in the filename.
For uniformity, this commit adds tests for DER encoded, SHA1-2DES and SHA1-RC4-128-encrypted RSA keys; for SHA1-3DES encrypted keys, these were already present.
This commit adds the commands used to generate the various RSA keys to tests/Makefile so that they can be easily
regenerated or modified, e.g. if larger key sizes or other encryption algorithms need to be tested in the future.
This commit adds test for the new library function mbedtls_rsa_check_params for
checking a set of RSA core parameters. There are some toy example tests with
small numbers that can be verified by hand, as well as tests with real world
numbers. Complete, partial and corrupted data are tested, as well the check for
primality exactly if a PRNG is provided.
This commit adds tests for the new library function mbedtls_rsa_export_raw.
Each test case performs the following steps:
- Parse and convert a set of hex-string decoded core RSA parameters into big
endian byte arrays.
- Use these to initialize an RSA context
- Export core RSA parameters as byte arrays again afterwards
- Compare byte strings.
Each test split is performed twice, once with successive and once with
simultaneous exporting.
This commit adds tests for the new library function mbedtls_rsa_export. Each
test case performs the following steps:
- Parse and convert a set of hex-string decoded core RSA parameters into MPI's.
- Use these to initialize an RSA context
- Export core RSA parameters as MPI's again afterwards
- Compare initial MPI's to exported ones.
In the private key case, all core parameters are exported and sanity-checked,
regardless of whether they were also used during setup.
Each test split is performed twice, once with successive and once with
simultaneous exporting.
This commit adds numerous tests for the new library functions mbedtls_rsa_import
and mbedtls_rsa_import_raw in conjunction with mbedtls_rsa_complete for
importing and completing core sets of core RSA parameters (N,P,Q,D,E) into an
RSA context, with the importing accepting either MPI's or raw big endian
buffers.
Each test is determined by the following parameters:
1) Set of parameters provided
We're testing full sets (N,P,Q,D,E), partial sets (N,-,-,D,E) and (N,P,Q,-,E)
that are sufficient to generate missing parameters, and the partial and
insufficient set (N, -, Q, -, E).
2) Simultaenous or successive importing
The functions rsa_import and rsa_import_raw accept importing parameters at
once or one after another. We test both.
3) Sanity of parameters
This commit adds test for the new library function mbedtls_rsa_deduce_moduli for
deducing the prime factors (P,Q) of an RSA modulus N from knowledge of a
pair (D,E) of public and private exponent:
- Two toy examples that can be checked by hand, one fine and with bad parameters.
- Two real world examples, one fine and one with bad parameters.
This commit adds tests for the new library function mbedtls_rsa_deduce_private
for deducing the private RSA exponent D from the public exponent E and the
factorization (P,Q) of the RSA modulus:
- Two toy examples with small numbers that can be checked by hand, one
working fine and another failing due to bad parameters.
- Two real world examples, one fine and one with bad parameters.
The tests only work for a specific number for MBEDTLS_X509_MAX_INTERMEDIATE_CA
so the check has been changed to confirm the default value, and to show an error
otherwise.
The test for MBEDTLS_NO_UDBL_DIVISION wasn't preserving it's own config.h
for the next test.
Also added comments to ARM Compiler 6 tests to better explain them.
The X509 test suite assumes that MBEDTLS_X509_MAX_INTERMEDIATE_CA is below the
hardcoded threshold 20 used in the long certificate chain generating script
tests/data_files/dir-max/long.sh. This commit adds a compile-time check for
that.
Some tests in ssl-opt.sh assumes the value 8 for the maximal number
MBEDTLS_X509_MAX_INTERMEDIATE_CA of intermediate CA's. This commit adds a check
before conducting the respective tests.
The RSA key generation test needs strong entropy to succeed. This commit captures the presence of a strong entropy
source in a preprocessor flag and only runs the key generation test if that flag is set.
The test for MBEDTLS_NO_UDBL_DIVISION wasn't preserving it's own config.h
for the next test.
Also added comments to ARM Compiler 6 tests to better explain them.
The entropy test suite uses a negative dependency "depends_on:!CONFIG_FLAG" for one of its tests. This kind of
dependency (running a test only if some configuration flag is not defined) is currently not supported and instead
results in the respective test case being dropped.
This commit adds support for negative dependencies in test cases.
The function `mbedtls_rsa_gen_key` from `test_suite_rsa.function` initialized a stack allocated RSA context only after
seeding the CTR DRBG. If the latter operation failed, the cleanup code tried to free the uninitialized RSA context,
potentially resulting in a segmentation fault. Fixes one aspect of #1023.
If we didn't walk the whole chain, then there may be any kind of errors in the
part of the chain we didn't check, so setting all flags looks like the safe
thing to do.
Inspired by test code provided by Nicholas Wilson in PR #351.
The test will fail if someone sets MAX_INTERMEDIATE_CA to a value larger than
18 (default is 8), which is hopefully unlikely and can easily be fixed by
running long.sh again with a larger value if it ever happens.
Current behaviour is suboptimal as flags are not set, but currently the goal
is only to document/test existing behaviour.
generate add ctest test-suites, with the --verbose argument to be given
to the test suites.
The verbose output will be shown **only** if ctest is run with `-v` parameter
The verbose argument is to the test-suites, only when run through `ctest`
This commit adds four tests to tests/ssl-opt.sh:
(1) & (2): Check behaviour of optional/required verification when the
trusted CA chain is empty.
(3) & (4): Check behaviour of optional/required verification when the
client receives a server certificate with an unsupported curve.
* gilles/IOTSSL-1330/development:
Changelog entry for the bug fixes
SSLv3: when refusing renegotiation, stop processing
Ignore failures when sending fatal alerts
Cleaned up double variable declaration
Code portability fix
Added changelog entry
Send TLS alerts in many more cases
Skip all non-executables in run-test-suites.pl
SSL tests: server requires auth, client has no certificate
Balanced braces across preprocessor conditionals
Support setting the ports on the command line
By default, keep allowing SHA-1 in key exchange signatures. Disabling
it causes compatibility issues, especially with clients that use
TLS1.2 but don't send the signature_algorithms extension.
SHA-1 is forbidden in certificates by default, since it's vulnerable
to offline collision-based attacks.
There is now one test case to validate that SHA-1 is rejected in
certificates by default, and one test case to validate that SHA-1 is
supported if MBEDTLS_TLS_DEFAULT_ALLOW_SHA1 is #defined.
SHA-1 is now disabled by default in the X.509 layer. Explicitly enable
it in our tests for now. Updating all the test data to SHA-256 should
be done over time.
With SHA-1 deprecation, we need a few certificates using algorithms in
the default support list. Most tests still use SHA-1 though.
The generation process for the new certificates is recorded in the makefile.
The ECJPAKE test suite uses a size zero array for the empty password
used in the tests, which is not valid C. This commit fixes this.
This originally showed up as a compilation failure on Visual Studio
2015, documented in IOTSSL-1242, but can also be observed with GCC
when using the -Wpedantic compilation option.
Fixed a bug in ssl_srv.c when parsing TLS_FALLBACK_SCSV in the
ciphersuite list that caused it to miss it sometimes. Reported by Hugo
Leisink as issue #810. Fix initially by @andreasag01; this commit
isolates the bug fix and adds a non-regression test.
Modify tests/scripts/check-doxy-blocks.pl to ensure that:
* It can only be run from the mbed TLS root directory.
* An error code is returned to the environment when a potential error
in the source code is found.
The test case was generated by modifying our signature code so that it
produces a 7-byte long padding (which also means garbage at the end, so it is
essential in to check that the error that is detected first is indeed the
padding rather than the final length check).
The modular inversion function hangs when provided with the modulus 1. This commit refuses this modulus with a BAD_INPUT error code. It also adds a test for this case.
The TLS client and server code was usually closing the connection in
case of a fatal error without sending an alert. This commit adds
alerts in many cases.
Added one test case to detect that we send the alert, where a server
complains that the client's certificate is from an unknown CA (case
tracked internally as IOTSSL-1330).
Added command line arguments --port and --proxy-port to choose the
ports explicitly instead of deriving them from the PID. This
facilitates debugging e.g. with Wireshark.
Fix a buffer overflow when writting a string representation of an MPI
number to a buffer in hexadecimal. The problem occurs because hex
digits are written in pairs and this is not accounted for in the
calculation of the required buffer size when the number of digits is
odd.
