Previously, ssl_ecrs_ske_start_processing was used to indicate that
the ServerKeyExchange has been fetched from the record layer, but
that parsing its ECDHE parameter component has been preempted by the
restartable ECP feature. On re-entry of ssl_parse_server_key_exchange()
in this state, the code would directly jump into the parsing routine.
However, the only non-reentrant code that's jumped over this way is
the record fetching routine mbedtls_ssl_parse_record(), which is now
made re-entrant by setting `ssl->keep_current_message = 1` in case of
pre-emption due to restartable ECC.
The ssl_ecrs_ske_start_processing state is therefore redundant and
can be removed, which is what this commit does.
The postprocessing code for the server-side incoming client key
exchange and the client-side outgoing client key exchange both
contain the same code-paths for building the premaster secret
depending on the chosen ciphersuite (e.g., for ECDHE-PSK,
concatenating the ECDHE secret with the chosen PSK).
This commit moves this common code to ssl_tls.c, allowing
client- and server-side to share it.
After and performing key generation operations,
the client-side outgoing ClientKeyExchange handling includes
code-paths to assembly the PreMasterSecret (PMS) from the
available keying material, the exact assembly procedure
depending on which ciphersuite is in use. E.g., in an
(EC)DHE-PSK ciphersuite, the (EC)DHE secret would be concatenated
with the PSK to form the PMS.
This assembly of the PMS logically can be done after the ClientKeyExchange
has been written and the respective keying material has been generated,
and this commit moves it to the new postprocessing function
ssl_client_key_exchange_postprocess().
Ideally, the PMS assembly could be done prior to writing the
ClientKeyExchange message, but the (EC)DHE API does currently
not allow splitting secret-generation and secret-export; as
long as that's the case, we to generation and exporting in the
message writing function, forcing PMS assembly to be done in
the postprocessing.
This commit adds declarations and dummy implementations for
the restructured outgoing client key exchange handling that
will replace the previous ssl_write_client_key_exchange().
The entry point for the CliKeyExchange handling that is called
from the handshake state machine is
`ssl_process_client_key_exchange()`,
splitting the processing into the following steps:
- Preparation
Compute the keying material to be sent.
* For (EC)DH: Pick parameters and compute PMS.
* For ECJPAKE: Run round 2
* For RSA: Encrypt PMS
- Writing: Prepare the writing of a new messae.
- Postprocessing: Update handstate state machine.
The subsequent commits will scatter the code from the previous
monolithic function ssl_write_client_key_exchange() among those
dedicated functions, commenting out each part of
ssl_write_client_key_exchange() that has already been dealt with.
This gradual progression is meant to ease reviewing. Once all
code has been moved and all changes explained,
ssl_write_client_key_exchange() will be removed.
After the rewrite of incoming record processing to use the internal
SSL record structure mbedtls_record (which contains the data_offset
field to indicate where the IV resides), this field is no longer
necessary.
Note: This is an API break.
The function mbedtls_ssl_in_hdr_len() is supposed to return the length
of the record header of the current incoming record. With the advent
of the DTLS Connection ID, this length is only known at runtime and
hence so far needed to be derived from the internal in_iv pointer
pointing to the beginning of the payload of the current incooing
record.
By now, however, those uses of mbedtls_ssl_in_hdr_len() where the
presence of a CID would need to be detected have been removed
(specifically, ssl_parse_record_header() doesn't use it anymore
when checking that the current datagram is large enough to hold
the record header, including the CID), and it's sufficient to
statically return the default record header sizes of 5 / 13 Bytes
for TLS / DTLS.
This function is often called when there's already an error code to handle,
and one of the reasons to introduce the pending of alerts was to _not_ have
another potential error code to take care of. Reflect this by making `void`
the return type of `mbedtls_ssl_pend_fatal_alert()`.
The code wants timer callbacks to be set (checked in fetch_input()), and can't
easily check whether we're using nbio, so it seems easier to require the
callbacks to be always set rather than only with nbio as was previously done.
The number of meaning of the flags will be determined later, when handling the
relevant struct members. For now three bytes are reserved as an example, but
this number may change later.
Enforce restrictions indicated in the documentation.
This allows to make some simplifying assumptions (no need to worry about
saving IVs for CBC in TLS < 1.1, nor about saving handshake data) and
guarantees that all values marked as "forced" in the design document have the
intended values and can be skipped when serialising.
Some of the "forced" values are not checked because their value is a
consequence of other checks (for example, session_negotiated == NULL outside
handshakes). We do however check that session and transform are not NULL (even
if that's also a consequence of the initial handshake being over) as we're
going to dereference them and static analyzers may appreciate the info.
This commit introduces the option MBEDTLS_SSL_CONF_SINGLE_HASH
which can be used to register a single supported signature hash
algorithm at compile time. It replaces the runtime configuration
API mbedtls_ssl_conf_sig_hashes() which allows to register a _list_
of supported signature hash algorithms.
In contrast to other options used to hardcode configuration options,
MBEDTLS_SSL_CONF_SINGLE_HASH isn't a numeric option, but instead it's
only relevant if it's defined or not. To actually set the single
supported hash algorithm that should be supported, numeric options
MBEDTLS_SSL_CONF_SINGLE_HASH_TLS_ID
MBEDTLS_SSL_CONF_SINGLE_HASH_MD_ID
must both be defined and provide the TLS ID and the Mbed TLS internal
ID and the chosen hash algorithm, respectively.
This commit introduces the option MBEDTLS_SSL_CONF_SINGLE_EC
which can be used to register a single supported elliptic curve
at compile time. It replaces the runtime configuration API
mbedtls_ssl_conf_curves() which allows to register a _list_
of supported elliptic curves.
In contrast to other options used to hardcode configuration options,
MBEDTLS_SSL_CONF_SINGLE_EC isn't a numeric option, but instead it's
only relevant if it's defined or not. To actually set the single
elliptic curve that should be supported, numeric options
MBEDTLS_SSL_CONF_SINGLE_EC_TLS_ID
MBEDTLS_SSL_CONF_SINGLE_EC_GRP_ID
must both be defined and provide the TLS ID and the Mbed TLS internal
ID and the chosen curve, respectively.
