This issue has been reported by Tuba Yavuz, Farhaan Fowze, Ken (Yihang) Bai,
Grant Hernandez, and Kevin Butler (University of Florida) and
Dave Tian (Purdue University).
In AES encrypt and decrypt some variables were left on the stack. The value
of these variables can be used to recover the last round key. To follow best
practice and to limit the impact of buffer overread vulnerabilities (like
Heartbleed) we need to zeroize them before exiting the function.
In the case of *ret we might need to preserve a 0 value throughout the
loop and therefore we need an extra condition to protect it from being
overwritten.
The value of done is always 1 after *ret has been set and does not need
to be protected from overwriting. Therefore in this case the extra
condition can be removed.
The code relied on the assumptions that CHAR_BIT is 8 and that unsigned
does not have padding bits.
In the Bignum module we already assume that the sign of an MPI is either
-1 or 1. Using this, we eliminate the above mentioned dependency.
The signature of mbedtls_mpi_cmp_mpi_ct() meant to support using it in
place of mbedtls_mpi_cmp_mpi(). This meant full comparison functionality
and a signed result.
To make the function more universal and friendly to constant time
coding, we change the result type to unsigned. Theoretically, we could
encode the comparison result in an unsigned value, but it would be less
intuitive.
Therefore we won't be able to represent the result as unsigned anymore
and the functionality will be constrained to checking if the first
operand is less than the second. This is sufficient to support the
current use case and to check any relationship between MPIs.
The only drawback is that we need to call the function twice when
checking for equality, but this can be optimised later if an when it is
needed.
Multiplication is known to have measurable timing variations based on
the operands. For example it typically is much faster if one of the
operands is zero. Remove them from constant time code.
Change the default entropy nonce length to be nonzero in some cases.
Specifically, the default nonce length is now set in such a way that
the entropy input during the initial seeding always contains enough
entropy to achieve the maximum possible security strength per
NIST SP 800-90A given the key size and entropy length.
If MBEDTLS_CTR_DRBG_ENTROPY_LEN is kept to its default value,
mbedtls_ctr_drbg_seed() now grabs extra entropy for a nonce if
MBEDTLS_CTR_DRBG_USE_128_BIT_KEY is disabled and either
MBEDTLS_ENTROPY_FORCE_SHA256 is enabled or MBEDTLS_SHA512_C is
disabled. If MBEDTLS_CTR_DRBG_USE_128_BIT_KEY is enabled, or if
the entropy module uses SHA-512, then the default value of
MBEDTLS_CTR_DRBG_ENTROPY_LEN does not require a second call to the
entropy function to achieve the maximum security strength.
This choice of default nonce size guarantees NIST compliance with the
maximum security strength while keeping backward compatibility and
performance high: in configurations that do not require grabbing more
entropy, the code will not grab more entropy than before.
Add a new function mbedtls_ctr_drbg_set_nonce_len() which configures
the DRBG instance to call f_entropy a second time during the initial
seeding to grab a nonce.
The default nonce length is 0, so there is no behavior change unless
the user calls the new function.
Add a new function mbedtls_ctr_drbg_set_nonce_len() which configures
the DRBG instance to call f_entropy a second time during the initial
seeding to grab a nonce.
The default nonce length is 0, so there is no behavior change unless
the user calls the new function.
The blinding applied to the scalar before modular inversion is
inadequate. Bignum is not constant time/constant trace, side channel
attacks can retrieve the blinded value, factor it (it is smaller than
RSA keys and not guaranteed to have only large prime factors). Then the
key can be recovered by brute force.
Reducing the blinded value makes factoring useless because the adversary
can only recover pk*t+z*N instead of pk*t.
mbedtls_ctr_drbg_seed() always set the entropy length to the default,
so a call to mbedtls_ctr_drbg_set_entropy_len() before seed() had no
effect. Change this to the more intuitive behavior that
set_entropy_len() sets the entropy length and seed() respects that and
only uses the default entropy length if there was no call to
set_entropy_len().
This removes the need for the test-only function
mbedtls_ctr_drbg_seed_entropy_len(). Just call
mbedtls_ctr_drbg_set_entropy_len() followed by
mbedtls_ctr_drbg_seed(), it works now.
Move the definitions of mbedtls_ctr_drbg_seed_entropy_len() and
mbedtls_ctr_drbg_seed() to after they are used. This makes the code
easier to read and to maintain.
mbedtls_hmac_drbg_seed() always set the entropy length to the default,
so a call to mbedtls_hmac_drbg_set_entropy_len() before seed() had no
effect. Change this to the more intuitive behavior that
set_entropy_len() sets the entropy length and seed() respects that and
only uses the default entropy length if there was no call to
set_entropy_len().
Fix a signed int overflow in mbedtls_asn1_get_int() for numbers
between INT_MAX+1 and UINT_MAX (typically 0x80000000..0xffffffff).
This was undefined behavior which in practice would typically have
resulted in an incorrect value, but which may plausibly also have
caused the postcondition (*p == initial<*p> + len) to be violated.
Credit to OSS-Fuzz.
Add a parameter to the p_validate_slot_number method to allow the
driver to modify the persistent data.
With the current structure of the core, the persistent data is already
updated. All it took was adding a way to modify it.
When registering a key in a secure element, go through the transaction
mechanism. This makes the code simpler, at the expense of a few extra
storage operations. Given that registering a key is typically very
rare over the lifetime of a device, this is an acceptable loss.
Drivers must now have a p_validate_slot_number method, otherwise
registering a key is not possible. This reduces the risk that due to a
mistake during the integration of a device, an application might claim
a slot in a way that is not supported by the driver.
If none of the inputs to a key derivation is a
PSA_KEY_DERIVATION_INPUT_SECRET passed with
psa_key_derivation_input_key(), forbid
psa_key_derivation_output_key(). It usually doesn't make sense to
derive a key object if the secret isn't itself a proper key.
Allow a direct input as the SECRET input step in a key derivation, in
addition to allowing DERIVE keys. This makes it easier for
applications to run a key derivation where the "secret" input is
obtained from somewhere else. This makes it possible for the "secret"
input to be empty (keys cannot be empty), which some protocols do (for
example the IV derivation in EAP-TLS).
Conversely, allow a RAW_DATA key as the INFO/LABEL/SALT/SEED input to a key
derivation, in addition to allowing direct inputs. This doesn't
improve security, but removes a step when a personalization parameter
is stored in the key store, and allows this personalization parameter
to remain opaque.
Add test cases that explore step/key-type-and-keyhood combinations.
